Posts

Chosen Solution i have many problem here , 23 June i buy second iphone online the condition so good , but i got problem when battery turn into 20% and opening big app (antutu, pubg, facetime, telegram) it always retart (but when i charge thats couldnt happen), then when battery down in 10% my phone getting slower and lag . many my friend say this because my battery and then they give me recomend to using 3utools for check my battery but after i check everything about my battery thats clean and not on problem ....

Chosen Solution I dropped my phone and half the display quit responding to touch. Everything else worked fine. I ordered and replaced the panel and afterwards it works fine for 10 seconds or so then doesnt respond to touch for 10 seconds or so. Locking the phone then unlocking resets it and it works fine right after unlocking for the 10 seconds. Im wondering if its a bad panel that ifixit sent me....

Chosen Solution I’ve recently replaced the digitizer on a first gen iPad Air and now the LCD glitches out. I can only reproduce the glitch after leaving the iPad inactive for 10-15 mins. Upon turning it on after 10-15 mins of inactivity, It glitches out for a few seconds, and then shows an image and works normally. Heres what i’ve tried: Disconnecting the LCD and reconnecting Making sure all of the cables are snug Resetting the iPad (Holding down power and home button) Powering off and powering back on...

Chosen Solution iPad Pro 11’ won’t turn on. The port is clean. It won’t turn on despite being fully charged. Unable to read diagnostics. hello Bernie, it’s been a while and you probably have done it by now. Maybe it will be useful to someone. Unable to read diagnostics because it does not start. If you look at the closer you will find that it is drawing approximately 200mA when you press the power button....

Chosen Solution My iPad 4 at&t won’t charge past 1% unless I put it in recovery mode, I’ve tried hard resetting, I’ve tried wiping the iPad, any ideas?? The charging port is working if you can charge through dfu, I would then suspect the battery before board issue of Tristar charging issues.

Chosen Solution After changing the screen on an iPhone 5c the proximity sensor does not work. After noticing it did not work I took the phone back apart and repositioned the front camera and proximity sensor. After a hard reset it still does not work. The front camera flex cable has no tears so I assume the problem lies on either the screen not allowing enough light or … That’s why I post this question on this forum....

Chosen Solution Hello, I have an iPhone 5s that goes to a black/blank screen but first the Apple Logo comes up. I replaced the screen on it, I’ve done hundreds of screen replacements before without a problem. I’m always careful with electronics since they tend to be very fragile (anti-static wristband and no metal tools). I tried searching up the issue on several other forum with no luck, I figured I could give it a shot to see if anyone else has come across this....

Chosen Solution iPhone 6s got wet grabbed it fast, shake shake shake. I went to your site. I had your kit; and opened the phone as shown. . Except for the area at the top I could find only one droplet of water on top of (just replaced) battery. Only now with the phone open, I do see a red dot by the aperture where the sims card was. I removed sims card during initial shaking/airing Is this RED DOT the sign of death?...

Chosen Solution Sorry if this is a dumb question, but I’m looking to customize my iPhone 6 and seems like they don’t sell custom colored rose gold home buttons for the 6 to match with custom housings. Was wondering if anyone here knew if these are reverse compatible? I remember the 4S home button worked with the 4, and the 3GS home button worked with the 3G. Let me know. Thanks....

Chosen Solution ‘‘Hi there. My iPhone 4S (model A1387) will not boot into iOS. iPhone boots up initially and displays the apple logo for 3 seconds. Then it goes to a blank screen for another 3 seconds and the process repeats . If charger disconnect its saying that its uncharged. I changed the battery! I tried a restore but I got the error No. 9 ! I tried to hold the home button and in the same time Sleep/Wake button , but same issue....

Chosen Solution @sam8823 “Now is it possible to damage T con board this way “ absolutely possible. Unlikely that you damaged the panel (sure always possible, but unlikely). “This “Also there were two conductive tapes between Lcd panels (one on left and one on right panel) and TV body. “ sounds odd. Post some good images of your Panel and the cables that enter the panel. Adding images to an existing question that way we can see what you see....

Chosen Solution Is PS4 working with SATA III SSD? Can I upgrade it for SATA III speed? I would say, no, unfortunately! SATA III (6GB\ps) is backwards compatible with SATA II (3GB\ps), so in english to all non-IT individuals, they WILL work in the console, just not at 6GB\ps but at 3GB\ps. IGN, yes, did do some testing, but the results can be misleading. You do receive faster times with an SSD, but naturally that would happen anyhow as that’s what they were built to accomplish....

Chosen Solution Hi a lot of people have been looking for a ASUS G20AJ teardown video or a really good write up with photos has anyone seen one or could do one that would be amazing I want to upgrade mine but its a tricky case. Check here: http://rog.asus.com/forum/forumdisplay.p… https://www.youtube.com/watch?v=k7NroUI3… Though this is the CB-version of the G20, I hope you find this one helpful https://rog.asus.com/forum/showthread.ph… yeah I have some great tear down videos on my channel, I was the same and didn’t find any one that had tear down videos on this....

Chosen Solution Just wondering because there does not seem to be any answer and there is no way to buy a replacement on Steam. Their’s no guides on iFixit’s Steam Deck page, but their is an article that details the device’s teardown, and it does talk about how easy it is to replace the screen. I suggest taking a look at it here. You’re looking for a replacement screen for your Steam Deck?...

Chosen Solution Was wondering if anyone had an idea of what the part number for the Keyboard FPC Connector is inside the Pavilion 15-n097xx models. I am having one !&&* of a time trying to find the board component online to order so I can replace the connector… Any help would be great! The only HP ZIF connector I have their different styles but the same length and pins…. Would it work?...

Chosen Solution It’s been super hot today and my MacBook Pro is not shutting down. The screen is blue and glitching, I also can’t move the mouse. The screen keeps going from this to black. What can I do to solve this? The picture helps! Sadly you’ve damaged your display ;-{ You’ll need a new display assembly: 13” MacBook Pro Display Assembly - Space Grey, Apple P/N 661-10037 13” MacBook Pro Display Assembly - Silver, Apple P/N 661-10357 Here’s the guide to putting it in MacBook Pro 13" Touch Bar 2018 Screen Replacement

Chosen Solution I cannot plug the charger into my tablet. It only goes part of the way in, then no further, as if something is blocking the way. Please help! Thank you.

Chosen Solution So there is this crack in my screen not a scratch and i am not sure how to get rid of it if someone know please say somthing thanks Im afraid the answer I have may not be what you were hoping to hear but it sounds like you will need a screen replacement. Unfortunately there are no guides for this repair on this site that I could find but a google search found a couple of youtube videos doing repairs to the stealth....

Chosen Solution i cant open my pictures and videos.. no thumnails ,what is that Do you have old or new memory card inside your phone and did you shared files over bluetooth from (exp. LG L Bello or some other) to Huawei? I have new memory card How did you get it to work i have a new memory card and now i cant open pictures or

Chosen Solution During fill up I have cold water and warm water but I don’t have hot water. Why not? mike anderson, sounds like your cold water inlet valve does not shut off, hence the cold and warm water. This could be caused by a sticking valve or a bad program. I’d replace the valve (less expensive) and re-evaluate after. If you can give us the exact model number of your washer we may be able to help you further....