Chosen Solution So my Ipad Air 2 has been dropped before, and the screen goes out, but siri and the sounds work and touchscreen works, so before I just power off and turn on then it worked. But right now the same scenario ipad screen blacked out again but when I turn off and on, it doesnt have light anymore, but using a flashlight, I can see the shadow of the apple logo coming out of the screen....
Chosen Solution Question says it all, is the 3rd generation iPad mini digitizer the same as the first two, interchageable like? No, they are not the same. Everything is the same except the finger print reader in the home button which has an extra ribbon that goes from the home button to the logicboard. So the 1st and 2nd Gen screen will not work on 3rd iPad Mini. We found this the hard way when we tried to repair an iPad Mini 3rd Gen....
Chosen Solution I replaced a charging port on an iPhone 5S (the owner said it was not charging properly after they dropped it in dirt and they cleaned it out- it looked pretty rough in the port). I tried to charge it before replacement and it did not charge. It started charging after I replaced the charging port but after getting to 4% quickly it dropped down quickly and died. I had it on a good (apple brand) charger all night and it only got to 17% and is now back down to 13%....
Chosen Solution I replaced the screen recently no issues until today phone was on 1% then a couple hours later screen was half black half white split vertically . I disconnected battery now wont turn on black screen. Update now the screen gets very hot on top right corner of the screen and stays black I actually tried with an old screen and it powers up except for the lines so maybe j need another screen ?...
Chosen Solution Hi there, recently my wifi option has been greyed out and Bluetooth continually spinning and after reading past questions, it seems I require a microsolderer to repair the logic board. However, will repairing the wifi chip on the logic board cause any functions to disable? (i.e. Face ID not working, True Tone disable) Would like to know before sending it in. Thanks in advance! @Kelvin Cheng wifi ic being replaced won’t affect the functions, face id and truetone has nothing to do with wifi
Chosen Solution Hi everyone, i want to know if is possible buil an iPhone X from zero! I’ve seen on internet that all the parts of an iPhone X 256gb cost about 400€ Can i buy all the parts and assembly it at home?? I want to build one for my birthday ♥️ I love Jack’s tenacity on building his own iPhone (your URL link)! You need to look a bit deeper on how he did this and the amount of time and effort it took!...
Chosen Solution I am having trouble identifying something on a pcb. I THINK its ground, but… It contacts this metal plate (why i think it might be the ground) on the inside of the earbud cover: Backside of pcb: The copper plate is likely the external connection to the charging case. You likely have a metal surface on the other side and you likely have a second contact somewhere else as well....
Chosen Solution Our craftsman 2400 was working fine we started moving the grass and all of a sudden it quit moving forward or backwards all the keys to the tires are there , clean filter , brand new battery , new gas , oil. Don’t know what the problem is There are a few things that could cause you to lose drive power Freewheel control is in the disengaged positionDebris on the steering plateMotion drive belt wornPark brake engaged Below is a manual for reference, hopefully this gets you up and going again https://www....
Chosen Solution It won’t turn on. It doesn’t seem to be charging. JCorley Gray start by checking your charger, your charging cable. Then check your connector and see if there is any lint etc occluding it and if the cable fits snug or if it is loose. If all of that checks out you will have to tear your tablet down and replace the battery. While you have it open you also want to check the charging port connector (solder joints etc....
Chosen Solution Hi everyone, I just turned on my TV (Samsung UN32J4000AF 32" Class). I noticed two thin red small vertical lines in the upper corner. I was wondering if this is fixable or not. I have include a few pictures of it. Thanks in advance to anyone who can answer. ‘’’++@billhates++’’’ those look like they are within the panel itself and are not repairable. You can try and find the right panel for a replacement or try to live with it since a new panel will most likely cost more than a new TV....
Chosen Solution Do I have to get a screen replace for my iPod touch 7 gen because I dropped it 4 times since I had it @jaxonpartin going by your symptoms and by your statements that it was dropped, I would start with a new display. There is always a possibility that this is a bad (disconnected) ribbon cable or even the logic board but until you open it up and start looking there just is no way to tell....
Chosen Solution The problem is: wherever there is a grey gradient I get stripes of different greys instead of a smooth fade. Is this a common problem or should I be contacting the warranty service? Hi, Have you tried using the OSD to calibrate the screen? If it doesn’t work invoke the warranty.
Chosen Solution Have a Sony cdr and the play back side reads disc error… Won’t play any type of CD ..I’ve used it very little.. Depending on the brand, some DVD players tend to be better about CD-R media then others, especially -RW. It may just be a poor compatibility disc; try using a different CD-R, like a Taio Yuden (preferably not from the value series, notated as VAL on the part number)....
Chosen Solution Is this Computer Capable of running 2007 ROBLOX Client with shadows? -4DF2007 Official YouTube. Hi, It seems that Robolox Client is a program for Mac OS so it won’t run on a PC, (or not easily anyway). PC’s are more suitable for Windows and Linux programs. The PC could run Robolox using Windows or Linux as it meets the system requirements of Robolox - just, i.e PC specs are CPU is 2GHz and max ram is 1GB (if this is the amount of ram what is installed)....
Chosen Solution I’m having trouble with my htc desire 626. It keeps coming up with error messages such as: unfortunately, com.android. settings has stopped and I can’t find my settings button. Unfortunately, com.aiqidii.mercury has stopped, I would like my phone to start working again, is there anything you can do to help me? My phone unfortunately. Phone has stopped way Unfortunately phone stopped haw repire
Chosen Solution So, I have a PS4 that is around 4 years old, clean with no dust or bugs, and has never been dropped or harmed by anyone or anything. However, starting about a month ago, my controllers will suddenly disconnect and won’t reconnect, and if I’m downloading something, the download will halt and indicate it can’t be downloaded. If I do a hard reset, the controller will reconnect, but how long or if it will work is absolutely unpredictable; sometimes it will work for days, and other times it will not....
Chosen Solution Hi, We moved into our house in 2012 and had an over the range microwave installed. We purchased it new prior to moving in. There was already a spot for it but the people who sold us the house took theirs with them. This microwave was an LG and it worked until 2014 where one day it just started popping and sparking from behind the control panel when I turned it on to cook something....
Chosen Solution I want to use my slate 21 k100 as my pc’s monitor. I need to use it for studio purposes. So what’s the best approach? Update (12/22/2018) I want to know if there is any hardware modification possible to input an hmdi to the lcd Thuthu only if you can design a driver board for the LCD panel. for that you will need the engineering diagram for the panel itself and you will need to know how to design a circuit to drive that panel....
Chosen Solution I would like to purchase Gopro Session microSD card slot. How can i get one? It already has a micro SD card slot…. just buy any micro SD card in the capacity you need
Chosen Solution I’d like to know where I can find the ID # for the instrument cluster for my 2005 Buick Rendezvous. I’ve been told there are 4 types and I need the specific number. I don’t know what other info I can add to find this answer. I just need to know where I can find the part # for the cluster. Here are available instrument clusters with different options for your Buick....
