Chosen Solution My microwave has been beeping every 20 seconds for the past 24 hours even though it has been unplugged during that time. I watched U Tube videos to learn how to disconnect the beeper but I am not able to identify the beeper on my motherboard. I have an image of the motherboard with all wires attached. Can anyone identify the beeper so that I can disable it?...
Chosen Solution After I turned the power button on the label maker seems to go blank after trying to type. I try pressing buttons, printing etc, but nothing appears on the screen. Check to see if the batteries are installed correctly. Also the batteries possibly are drained and need to be replaced. Also if you use a Ac adapter check to see if it is plugged in and pushed into the label maker correctly....
Chosen Solution So I Spilled a little bit of water on my home button this morning and quickly wiped it off but I’m still a little bit worried that there is still water in there. What should I do? There’s a rubber seal round the button inside the screen assembly, you should be ok if it’s still working. If you’re overly worried stick in a sealed Tupperware box covered in rice for 24-48hrs
Chosen Solution Hello. I changed the hard drive (1TB original to Kingston SSD 960 GB) on my iMac EMC 2544, Late 2012 13,1. After that, I had exactly the same problem. iMac fan starts after shutdown Fan runs after shutdown and when iMac goes into sleep mode. Can you advise me of anything? After installing the old hard drive back, nothing has changed. Update (05/01/2017) http://imgur.com/a/nSJsW How about installing this app so we can see what your systems thermal management is up to here: TG Pro....
Chosen Solution I got an iPhone 5s that drain the battery quickly and it doesn’t recognize the lightning cable . At first I thought that replacing the battery would solve the problem but it didn’t work. So I think that the problem is caused due logic board short cause when I touch it after using the iPhone for a while it gets hot. I have doubts about when it is necessary to change the pm8018 or the 1610A1...
Chosen Solution Dear users, i got 2 probems with my phone, 7 months ago my bluetooth start to failing and every time i connect it to an device , the sound is crunchy like it has a bad connection, also when i hold my hand in the top right corner of the frame, its worse. is there anyway to fix this? also i recently changed my housing and i used a complete housing, i have problems with my cell-antenna now....
Chosen Solution Okay, so I’ve just finished replacing an iPhone 6 screen (switching over the original home button), however I’ve now found that the home button does not work at all. I have tried a different home button to test the flex cable attached to the backplate and that works fine so it’s not that. I believe I must have damaged the home button itself/it’s flex cable when removing it from the original screen....
Chosen Solution Hello everyone here is the thing my face iphone cam is foggy compared to other iphone 6s (watch the pictures) Then i just saw that i had like dust in the front of my iphone like between the glass and the lens i can see it it’s not all black there is like dust inside, im not a phone technician or something, but a computer one so i know how to open things etc my questions is can i open the iphone and clean it inside ?...
Chosen Solution I have an iPhone 6 that was dropped and wouldn’t turn on anymore. We though it was just a bad screen so we changed the screen. It won’t boot up. It will connect to itunes but itunes says its in recovery mode and to restore. (Nothing shows on iPhone screen). It will try restoring and it says waiting for iPhone. After awhile it will show the Apple logo on the iPhone then stay like that until Itunes gives the cannot restore error 4014 error....
Chosen Solution My iPhone 3GS keeps getting disconnected from the USB port of my Mac Mini. I have tried restarting the phone and the mini as well as various other tricks found on Google. When the phone is connected to the USB port, it gives the “charging” beep and sometimes it immediately disconnects while at other times it loses the connection after a minute or two. I have tried changing ports, using a different cable and connecting it to my PC, everything yielded the same fruitless result :( Could anyone help with this please?...
Chosen Solution I have this iphone 6 motherboard that works almost fine, exept it wan’t recognise the charging cable, and the message pops up: “This accessory may not be supported”. I have tried “millions” of different cabels, originals too, but it dosn’t work. I can charge it by turning the phone of while it is plugged in, but that is no good… I have tried with diferent ports too, dosn’t make a difference....
Chosen Solution i think rthe port i plug my charging cable is loose can that be fixed Hi @bitchpudding76 Here is an image, taken from the ifixit Alcatel One Touch Evolve 2 Main Circuit Board Replacement guide (Step.8), which shows the charge port in your phone. (click on image to enlarge for better viewing) The guide shows how to open the phone to gain access to the mainboard so that the micro USB charge port can either be re-soldered back onto the circuit board or replaced if it is faulty....
Chosen Solution Hello, I posted here because I buy an used Macbook Pro, but I observed the keyboard backlight didn’t work (on MacOS or Linux). So I checked the hardware : a cable is half cutted (close the the right fan, I don’t have photo yet). So I suppose it is the cable of the backlight keyboard. So : can I fix simply and without change the keyboard this backlight cable ?...
Chosen Solution Sometimes my keyboard does not work. And it will be back to normal after a short while( about 1 to 3 minutes). Have you tried to reset the operating system back to the factory default? perhaps this can help.
Chosen Solution Hi, we just replaced the display from an iPhone 6S and found that when typing the cursor sometimes jumps into another place by itself. Everything else works fine including 3D. We tried another display, same issue. The original display works fine though. Any ideas? Sounds like you have bought a copy display, which are known for this issue. Quality is key with this model iPhone. You will not get this issue with original quality displays....
Chosen Solution a Mitsubishi large screen TV. The sound needs to be at the highest level or you cannot hear the sound.can this be fixed? Hello Chris and Pearl, Have you checked to see if you have other devices connected to the TV that can have their own volume controls and can cause the TV to have low volume if their volume settings are low. Some cable boxes can have such controls, along with standalone DVD players or DVRs....
Chosen Solution I have the same problem. I am missing 2 bars… get very poor signal after a screen change. I did it to three phones…all the same problem. I am doing something wrong. The cable is attached properly. My wi-fi, bluetooth and everything is fine. just GSM signal is poor. Any thoughts? When you replace an iPhone 4 screen you are required to take out the antenna bridge assembly (the part that gives signal to your phone)....
Chosen Solution I need halp EMI shield I don’t know what is it screws to remove it I don’t know what screws bit to use ? Update (03/08/2018) I don’t want screws is it It’s just standard phillips PH000 screw bit you need.
Chosen Solution I wrote with Sharpie like an idiot months ago, and I googled earlier how to get Sharpie off a surface, and I saw nail polish remover. I folded a little bit of toilet paper and gave it a good amount of polish remover. I let it sit on the drawn surface for about 8 seconds. I took it off and the bottom of the TP was stuck. It was peely for 5 seconds and now it’s stuck there....
Chosen Solution hi I am new to this but fairly practical. i have bought a late 2009 27 inch iMac and want to give it a ‘boost’. Looking at the forums, it seems that ‘more memory’ and changing the drive to a SSD are my 2 options. Can anyone advise on which to do first/ which kit to buy? Thank you in advance! Yes upgrading the ram and HDD to SSD will be great....
